HOMEProducts10 Inch Loudspeaker DriversSOVEREIGN PRO 10-300SC
Fane Sovereign Pro 10-300SC Fane Sovereign Pro 10-300SC
TFane Sovereign Pro 10-300SC TFane Sovereign Pro 10-300SC


Bass Driver

Data Sheet
(0 Reviews)  Review this item
  • 600 W Program Power.
  • 98 dB Sensitivity (1W/1m).
  • Highly versatile in two-way ported enclosures.
  • Warm and smooth response throughout the bass frequency range.
  • Specially formulated cone coating provides HF vocal clarity.
  • Optimised cone pulp offering increased strength, durability and performance.
  • Long throw motor and high-linearity suspension system allow solid bass reproduction.
  • Perfect for full range KTV systems.
  • 2.5-inch Copper clad aluminium voice coil.

The Sovereign Pro 10-300SC is intended for use in two-way ported enclosures such as the classic bass driver plus horn tweeter or compression driver format. The unit features die cast chassis with long throw motor system and high linearity suspension allowing solid bass reproduction at high-power levels. The specially formulated cone pulp allows this driver to give a warm and smooth response throughout the bass frequency range and delivers well balanced tonal characteristics when properly matched to appropriate high-frequency drivers. The Sovereign Pro 10-300SC is designed for use in 25 to 50 Litre ported enclosures and features a 2.5 inch voice coil, 300 Watt power handling and 98 dB sensitivity.


  • Please enquire about alternative impedances.
  • A.E.S. power handling test. Pink noise bandpass filtered at 12 dB per octave with cutoff frequencies of 50 Hz and 500 Hz. Driver mounted in free air, test signal applied at rated power for two hours.
  • Please note that the frequency response measurements are supplied for comparison only and are not a measure of the low frequency performance which may be achieved in a fully optimised system.
Electro Acoustic Specifications
Nominal Chassis Diameter 10" / 254 mm
Impedance 8 Ω
Power Handling 300 W (A.E.S.)
Peak Power (6dB Crest Factor) 1200 W (A.E.S.)
Usable Frequency Range (-6dB) 45 Hz - 4 kHz
Sensitivity (1W - 1m) Wideband 98 dB
Moving Mass (inc. Air Load) 46.8 grams
Minimum Impedance (Zmin) 6.24 Ω
Effective Piston Diameter 8.19" / 208.02 mm
Magnet Weight 56 oz
Magnetic Gap Depth 0.31" / 7.87 mm
Flux Density 1.1 Tesla
Coil Winding Height 0.53" / 13.46 mm
Voice Coil Diameter 2.5" / 63.5 mm
Speaker Type Bass Driver
Speaker Series The Professional Series
Program Power 600 W (A.E.S.)
Sensitivity (1W / 1m) Working band
Thiele Small Parameters (TSPs)
FS 47 Hz
Re 5.5 Ω
QMS 10.13
QES 0.34
QTS 0.33
Vas 45.43 Litres
Vd 0.172 Litres
CMS 0.245 mm/N
BL 14.8 T/m
MMS 46.8 grams
Xmax 4.75 mm
Sd 361 cm2
Efficiency 1.70%
Le 1.27 mH
EBP 138.24 Hz
Materials of Construction
Coil Former Material Kapton
Voice Coil Material CCAW
Magnet Material Ferrite
Chassis Material Die-cast Aluminium
Cone Material Curvilinear Paper
Surround / Edge Termination Polyvinyl Damped Dbl. Half Roll Linen
Dust Dome Material Solid Paper
Connectors Push-button Spring Terminals
Polarity Positive voltage at red terminal causes forward motion of cone
Mounting / Shipping Information
Overall Diameter 11.16" / 283.4 mm
Width Across Flats 10.343" / 262.7 mm
Flange Height 0.305" / 7.8 mm
Baffle Hole Diameter F/M 8.97" / 227.83 mm
Baffle Hole Diameter R/M N/A
Gasket Supplied Rear
Outer Fixing Holes 4x ø 0.218" on 10.625" PCD / 4x ø 5.5 mm on 270 mm PCD
Inner Fixing Holes Not Applicable
Depth 4.37" / 111 mm
Weight 10.14 lb / 4.6 Kg
Recommended Enclosure Volume 0.88 - 1.76 cu ft / 25 - 50 Litres
Shipping Weight 11.35 lb / 5.15 Kg
Packing Carton Dimensions (W) 275 (D) 275 (H) 150 mm
DescriptionSizeFormatGet File
Fane Sovereign Pro 10-300SC Datasheet0.18Mb.pdfDOWNLOAD
Stay connected. Get fresh content from Fane to your email box
© 2016 Fane International Limited. All rights Reserved. Site developed by Edoru web design Wakefield
You've reached the maximum comparison limit of four products.
Please choose one of the following options....