JOIN US AT The GETshow 2019 - Stand 1A-08 — 8 - 11th May 2019 | Guangzhou, China

HOMEProductsArchive - OEMCOLOSSUS 18-800N
Fane Colossus 18-800N Fane Colossus 18-800N
TFane Colossus 18-800N TFane Colossus 18-800N

COLOSSUS 18-800N

Bass Driver

Data Sheet
(0 Reviews)  Review this item
£POA
RRP Inc. VAT
AVAILABILITY : OUT OF STOCK
  • DISCONTINUED. Available for SPECIAL ORDER / OEM only.
  • Lightweight neodymium magnet assembly.
  • Weighs only 7.55 kg.
  • Tight punchy bass combined with high levels of excursion.
  • Laminated silicone suspension.
  • Delivers bass down to 35 Hz in a 200 Litre ported enclosure.

The Colossus 18-800N is intended for use as a high-output bass driver in multi way systems. It features a 4 inch 'sandwich' inside and outside windings voice coil immersed in a symmetric magnetic field yielding increased linearity and lower distortion. This, coupled with a large Xmax of 8 mm and laminated silicone suspensions, ensures tight, punchy bass at high levels of excursion. The cone membrane, manufactured from polycellulose, is much stronger and more durable than conventional paper pulp alternatives. This allows the driver to combine high-sensitivity with the structural integrity required to produce undistorted low frequencies at extreme sound pressure levels. The driver handles 800 Watts (A.E.S) continuous and can cope with peaks in excess of 3200 Watts. This is due to advanced thermal management in the form of vented die-cast chassis and increased motor system venting. These measures effectively remove heat from the voice coil, resulting in extremely low-power compression. The Colossus 18-800N exhibits 101 dB sensitivity and can deliver bass down to 35 Hz (-6 dB) in a 200 Litre ported enclosure.

 

  • Please enquire about alternative impedances.
  • A.E.S. power handling test. Pink noise bandpass filtered at 12 dB per octave with cutoff frequencies of 40 Hz and 400 Hz. Driver mounted in free air, test signal applied at rated power for two hours.
  • Please note that the frequency response measurements are supplied for comparison only and are not a measure of the low frequency performance which may be achieved in a fully optimised system.
Electro Acoustic Specifications
Nominal Chassis Diameter 18" / 457.2 mm
Impedance 8 Ω
Power Handling 800 W (A.E.S.)
Peak Power (6dB Crest Factor) 3200 W (A.E.S.)
Usable Frequency Range (-6dB) 36 Hz - 2 kHz
Sensitivity (1W - 1m) Wideband 101 dB
Moving Mass (inc. Air Load) 148 grams
Minimum Impedance (Zmin) 6.5 Ω
Effective Piston Diameter 14.84" / 376.93 mm
Magnet Weight N/a
Magnetic Gap Depth 0.43" / 11 mm
Flux Density 1.1 Tesla
Coil Winding Height 0.87" / 22 mm
Voice Coil Diameter 4.0" / 101.6 mm
Speaker Type Bass Driver
Thiele Small Parameters (TSPs)
FS 38 Hz
Re 5.2 Ω
QMS 5.27
QES 0.325
QTS 0.306
Vas 217 Litres
Vd 0.95 Litres
CMS 0.12 mm/N
BL 24 T/m
MMS 148 grams
Xmax 8 mm
Sd 1133 cm2
Efficiency 3.50%
Le 1.96 mH
EBP 116.92 Hz
Mounting / Shipping Information
Overall Diameter 19.1" / 485 mm
Width Across Flats 18" / 457.2 mm
Flange Height 0.465" / 11.8 mm
Baffle Hole Diameter F/M 16.53" / 419.86 mm
Baffle Hole Diameter R/M 16.33" / 414.78 mm
Gasket Supplied Front & Rear
Outer Fixing Holes 8x ø 0.275" on 18.425" PCD / 8x ø 7 mm on 468 mm PCD
Inner Fixing Holes 8x ø 0.275" on 17.25" PCD / 8x ø 7 mm on 438.15 mm PCD
Depth 7.79" / 198 mm
Weight 16.10 lb / 7.55 Kg
Recommended Enclosure Volume 4.41 - 14.12 cu ft / 125 - 400 Litres
Shipping Weight 22 lb / 9.55 Kg
Packing Carton Dimensions (W) 485 (D) 485 (H) 230 mm
DescriptionSizeFormatGet File
Fane Colossus 18-800N Datasheet0.28Mb.pdfDOWNLOAD
Stay connected. Get fresh content from Fane to your email box
SUBSCRIBE
© 2016 Fane International Limited. All rights Reserved. Site developed by Edoru web design Wakefield
PRODUCT COMPARISON
You've reached the maximum comparison limit of four products.
Please choose one of the following options....
VIEW COMPARISIONS